Tecnichal data
| Degree of protection (IP) | IP20 |
| Shock | 15 G peak for 11 ms duration (ñ1.0 ms) |
| PWM frequency | 2 kHz @ 690V AC |
| Vibration | 0.152 mm (0.006 inch) displacement, 1 G peak |
| Number of analogue outputs | 2 |
| Mains voltage | 690 V |
| Integrated breaking resistance | No |
| Brake IGBT | Brake IGBT installed |
| Internal communication module | No communication module |
| Input voltage rating | 690V AC, 3-phase, 50 Hz |
| AC input undervoltage trip | Frames 5â⬦6: 345V AC @ 600/690V |
| Bus voltage, nom | Frames 0…5: 932V DC @ 600/690V |
| Bus undervoltage shutoff/fault | Frames 0…5: 437V DC @ 600/690V |
| Bus overvoltage trip | Frames 0…5: 1162V DC @ 600/690V |
| Output voltage rating | 0…690V AC @ 690V AC, 1-phase |
| Circuit breaker current rating, max | 375 A @ 690V AC, 3-phase, normal duty |
| Output current rating, continuous | 98 A @ 690V AC, 3-phase, normal duty |
| Output current rating, 1 min | 123 A @ 690V AC, 3-phase, heavy duty |
| Output current rating, 3 sec | 140 A @ 690V AC, 3-phase, heavy duty |
| Logic control ride-thru | 0.5 seconds minimum, 2 seconds typical |
| Brake resistor | No internal brake resistor |
| Input current rating | 94.7 A @ 690V AC, 3-phase |
| Documentation | Manual |
| Carrier frequency | 2, 4, 8, and 10 kHz. Drive rating based on 4 kHz |
| Encoder quadrature | 90 degrees, ñ27 degrees at 25 ðC (77 ðF) |
| AC input overvoltage trip | Frames 5…6: 818V AC @ 600/690V |
| Input power rating | 94.4 kVA @ 690V AC, 3-phase, heavy duty |
| Dual element time delay fuse current rating | 125…200 A @ 690V AC, 3-phase, normal duty |
| Non-time delay fuse current rating | 125…375 A @ 690V AC, 3-phase, normal duty |
| Digital input latency, typical | 9.2 ms @ stop signal for SVC motor control |
| Heat sink thermistor | Monitored by microprocessor overtemp trip |
| Digital input latency | 9.2…16.0 ms @ start signal for SVC motor control |
| Drive to motor power ratio, max | Recommended not greater than 2:1 ratio |
| Stop modes | Multiple programmable stop modes including ââ¬Ã¢ Ramp, Coast, DC-brake, Fast brake, Ramp-to-hold and S-curve |
| Frequency accuracy | Digital input: within ñ0.01% of set output frequency |
| Acceleration/deceleration | Two independently programmable accel and decel times. Each time can be programmed from 0…3600 seconds in 0.1 second increments |
| Analog input latency, typical | 6.4 ms @ speed signal for SVC motor control |
| Number of digital inputs | 6 |
| Number of digital outputs | 3 |
| Number of analogue inputs | 2 |
| Internal watts loss | 407 W @ 690V, 90 Hp normal duty (IP20, NEMA/UL Type 1) |
| Supporting protocol for DeviceNet | Yes |
| Human interface model | No HIM (blank plate inserted) |
| Max. output frequency | 420 Hz |
| External watts loss | 1389 W @ 690V, 90 Hp normal duty (IP20, NEMA/UL Type 1) |
| Total watts loss | 1796 W @ 690V, 90 Hp normal duty (IP20, NEMA/UL Type 1) |
| Supporting protocol for EtherNet/IP | Yes |
| Mains frequency | 50 Hz |
| Actual short circuit rating | Determined by AIC rating of installed fuse/circuit breaker |
| Internal EMC filtering | With EMC filter with common mode choke |
| Custom drive/firmware | No custom firmware |
| Feedback option | No feedback |
| Analog input latency | 4.8…12.4 ms @ speed signal for SVC motor control |
| Torque regulation | Without feedback: ñ5 %, 600 rad/sec bandwidth |
| Enclosure type | IP20/NEMA/UL Type 1 |
| Output current rating | 98 amps, 90 kW normal duty, 75 kW heavy duty, frame 6 |
| Control options | Vector control with 24V DC I/O |
| Drive overcurrent trip | Instantaneous current limit: 220…300% of rated current (dependent on drive rating) |
| Efficiency | 97.5% at rated amps, nominal line volts |
| Encoder supply | 12V, 250 mA. 12V, 10 mA minimum inputs isolated with differential transmitter, 250 kHz maximum |
| Speed control-speed regulation | Without feedback (Vector Control Mode): 0.1 % of base speed across 120:1 speed range, 120:1 operating range, 50 rad/sec bandwidth |
| Current limit capability | Proactive current limit programmable from 20…160% of rated output current, Independently programmable proportional and integral gain |
| Selectable motor control | Sensorless vector with full tuning. Standards V/Hz with full custom capability and vector control |
| Frequency control-speed regulation | With slip compensation (Volts per Hertz mode): 0.5% of base speed across 40:1 speed range, 40:1 operating range, 10 rad/sec bandwidth |
| Input phases | 3-phase input provides full rating for all drives. 1-phase operation possible on certain drives and provides 50 % of rated current. Frames 0…6: drive can be supplied as 6 pulse or 18 pulse in an engineered package. |
| Control method | Sine coded PWM with programmable carrier frequency, ratings apply to all drives, the drive can be supplied as 6 pulse or 18 pulse in an engineered solution |
| Encoder requirements | Encoders must be line driver type, quadrature (dual channel) or pulse (single channel), 8…15V DC output (4…6V DC when jumpers are in 5V position), single-ended or differential and capable of supplying a min. of 10 mA per channel, maximum input frequen |
| Number of phases output | 3 |
| Number of phases input | 3 |
| Relative symmetric net voltage tolerance | 10 % |
| With control element | Yes |
| Supporting protocol for LON | Yes |
| Supporting protocol for TCP/IP | Yes |
| Supporting protocol for PROFIBUS | Yes |
| Supporting protocol for CAN | Yes |
| Supporting protocol for Modbus | Yes |
| Motor overload protection | Frames 0…6 vector control: powerflex 700 drives with vector control, which is identified by a C or D in position 15 of the catalog number, provide class 10 motor overload protection according to NEC article 430 and motor overtemperature protection acco |
| Input frequency tolerance | 47 Hz |
| Encoder duty cycle | 50% ñ10% |
| Displacement power factor (all drives) | 0.98 across speed range |
| Short circuit rating, max | 200000 amps symmetrical |
| Output voltage range | 0 to rated motor voltage |
| Encoder type | Incremental, dual channel |
| Power ride-thru | 15 milliseconds at full load |
| Short circuit trip | Phase-to-phase on drive output |
| Ground fault trip | Phase-to-ground on drive output |
| Drive to motor power ratio, min | Recommended not less than 1:2 ratio |
| Control logic noise immunity | Showering arc transients upto 1500V peak |
| Line transients | Up to 6000 volts peak per IEEE C62.41-1991 |
| Intermittent overload | 110% overload capability for up to 1 minute, 150% overload capability for up to 3 seconds |
| Height, approx | IP54, NEMA type 12 standalone: 1828.8 mm |
| Depth, approx | IP54, NEMA type 12 standalone: 487.8 mm |
| Width, approx | IP54, NEMA type 12 standalone: 711.3 mm |
| Weight, approx | IP54, NEMA type 12 standalone: 229.07 kg (drive and packaging weight) |
| Sound level | Frame 6: 72 dB @ 300 CFM fan velocity |
| Altitude | 1000 m (3300 ft.) maximum without derating |
| Degree of protection (NEMA) | 1 |
| Surrounding air temperature | IP20, NEMA/UL type 1 (with top label): 0…50 ðC (0…122 ðF) @ frames 5â⬦6, most ratings |
| Atmosphere | Drive must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust, If the drive is not going to be installed immediately, store the drive where it is not exposed to a corrosive atmosphere |
| Operating temperature | 40 ðC @ 690V AC |
| Storage temperature | -40 ðC |
| Relative humidity | 5…95% noncondensing |
| Pollution degree 1 according to EN 61800-5-1 | No pollution occurs, only dry non-conductive pollution occurs, and has no influence |
| Pollution degree 4 according to EN 61800-5-1 | The pollution generates persistent conductivity caused, for example, by conductive dust, rain or snow |
| Pollution degree 3 according to EN 61800-5-1 | Conductive pollution occurs, dry non-conductive pollution occurs and becomes conductive due to condensation |
| Pollution degree 2 according to EN 61800-5-1 | Normally only non-conductive pollution occurs, Occasionally a temporary conductivity, caused by condensation is expected when the drive is out of operation |
| Surrounding environment pollution degree | All enclosures are acceptable for pollution degree 1 and 2, an enclosure that meets or exceeds IP54, NEMA/UL Type 12, is required for pollution degree 3 and 4 |
